Scag Power Equipment GC-STWC-61 User Manual

MODEL GC-STWC-61THIS MANUAL CONTAINS THE OPERATINGINSTRUCTIONS AND SAFETY INFORMA-TION FOR YOUR SCAG ACCESSORY. READ-ING THIS MANUAL WILL PROVIDE YOU

8GC-STWC BLOWER HOUSING ASSEMBLYWARNINGINSTALL BELT COVER BEFOREOPERATING MACHINEREAD OPERATOR'S MANUAL2005 GC Blower Assembly1233454745456789910

9GC-STWC BLOWER HOUSING ASSEMBLYRef. PartNo. Number Description1 04067-07 Pin, Ring 2-1/4" Long2 481547 Lanyard, Deck Height Pin3 04019-0

10GC-STWC 61" BLOWER MOUNTING COMPONENTSGC-STWC-61 Blower Attachment PartsRIGHT SIDE OF 61"CUTTER DECK SHOWN 123456678910101112131415

11Ref. PartNo. Number Description1 483226 Belt Cover, GC-STWC - 61"2 04029-04 Wingnut, Plastic 3/8" Small3 482300 Cap, Square Vinyl4 04021-0

12GC-STWC BUCKET SUPPORT COMPONENTS (UPPER)12344685599995115161616161616181813131920142121222323243111532333326272829303233637352531353817159344571210

13GC-STWC BUCKET SUPPORT COMPONENTS (UPPER)Ref. PartNo. Number Description1 423302 Screen, Catcher Hood2 04090-02 Pop Rivet, 3/16 x .6523 0404

14GC-STWC BUCKET SUPPORT COMPONENTS (LOWER)STC 2008 BSC12111415161718192021222324413546784381267445FRAME951010ATO "A"3669"A"2526

15GC-STWC BUCKET SUPPORT COMPONENTS (LOWER)1 04090-02 Pop Rivet, 3/16 x .6522 482321 Seal, Hood3 423262 Tube, Upright4 04041-07 Flatwasher, 3/8-.391 x

16GC-STWC DECALS483402482275481327483391483392483393483044483392483391483393 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS:

LIMITED WARRANTY- COMMERCIAL ACCESSORYAny part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or se

PART NO. 03229PRINTED 3-2007PRINTED IN USA© 2007SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INCWWW.SCAG.COM

11.1 INTRODUCTIONThis manual has been prepared to provide theinformation you need to correctly assemble, operate,and maintain this grass catcher. Read

2WARNINGWARNINGDO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHINGKIT, OR ENTIRE GRASS CATCHER INSTALLED3.1 ASSEMBLY INSTRUCTIONS FOR 61" CUTTE

3FIGURE 3-2FIGURE 3-3ELASTIC STOPNUTFLATWASHERCARRIAGE BOLTRIGHT SIDE OF CUTTER DECK SHOWN(Note: Some parts not shown for viewing purposes.) 2005 GC-S

410. Install the new belt covers and secure. See itemsnumber 1 and number 21 on page 8 of the BlowerMounting Components section in the IllustratedPar

51. Prepare the machine so there is easy and safeaccess to the work area. Remove the key andmaintain all safety related work procedures.Always wear e

65.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS* Perform these maintenance procedures more frequently under extreme dusty or dirty condition

7NOTES