Scag Power Equipment GC-STC-CSV User Manual

MODEL GC-STT-CSVTHIS MANUAL CONTAINS THE OPERATINGINSTRUCTIONS AND SAFETY INFORMA-TION FOR YOUR SCAG ACCESSORY. READ-ING THIS MANUAL WILL PROVIDE YOU

81. Prepare the work area making sure that it is aclean, safe environment.2. Remove the rubber strap holding the adapter tothe blower assembly. See F

95.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.

10GC-STT-V BLOWER HOUSING ASSEMBLY2005 GC V+ Blower Assembly454745478991010111112121314141414151516171819202122232424272728303131323334353537383940414

111 04067-07 Pin, Ring 2-1/4" Long2 481547 Lanyard, Deck Height Pin3 04019-02 Nut, Serr. Flange 1/4-204 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4&qu

12GC-STT-V BLOWER MOUNTING COMPONENTSUNDER SIDE OFVELOCITY-PLUSCUTTER DECK SHOWN232328242425252626161625271234566789101011121314151516171819202006 GC-

13GC-STT-V BLOWER MOUNTING COMPONENTSRef. PartNo. Number Description1 483225 Belt Cover, GC-STT - 52"483227 Belt Cover, GC-STT - 61"2 04029-

14GC-STT-CSV HOPPER COMPONENTSAABBCC2006 GC-STT-CSV Hopper 11645151445435655617415054349315111405859251289344950 2434294227483853103361603719362049332

15GC-STT-CSV HOPPER COMPONENTSRef. PartNo. Number Description1 483038 Hopper, GC-STT-CS2 482732 Door, GC-CS3 461626 Sweeper Weldment, GC-CS4 4

16GC-STT-CSV DECALS481039482275481327483037481377482080483044

LIMITED WARRANTY- COMMERCIAL ACCESSORYAny part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or se

PART NO. 03187PRINTED 7-2005PRINTED IN USA© 2005SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INCwww.scag.com

11.1 INTRODUCTIONThis manual has been prepared to provide theinformation you need to correctly assemble, operate,and maintain this grass catcher. Rea

2A. Disengage the deck drive, apply the parkingbrake and allow all moving parts to come toa complete stop.B. Pull downward on the hopper door handle t

33.1 ASSEMBLY INSTRUCTIONS-NOTE-Use the illustrated parts list as a part numberreference when following the assemblyinstructions.1. Remove all packagi

4PROPERLYSERVICEENGINEWITHOILANDFUEL.DISCHARGE CHUTE OPENINGFRONT OF CUTTER DECKREAR OF CUTTER DECKVIEW FROM RIGHT SIDE OF CUTTER DECKFigure 2-52"

5FIGURE 3-48. Install the blower assembly to the mountingbracket and secure with the mounting pin andhair pin. See Figure 3-4.9. Align the blower ass

613. Install the hopper mounting brackets (p/n 451512& p/n 451595) to the outside of the frame on therear of the machine using 3/8-16 x 1" he

7FIGURE 3-7Liquid Cooled OnlyNote:Illustration is for reference only. Some parts have been removed for visual purposes and may vary depending on model