Scag Power Equipment SFZ User Manual

MODEL GC-SFZTHIS MANUAL CONTAINS THE OPERATINGINSTRUCTIONS AND SAFETY INFORMA-TION FOR YOUR SCAG ACCESSORY. READ-ING THIS MANUAL WILL PROVIDE YOUWITH

8FIGURE 3-191/2-13 x 1-1/4”1/2” FLATWASHER1/2” FLATWASHER1/2-13 SERRATEDFLANGE NUTWEIGHT ASSEMBLY (2X)1/2-13 x 1-1/4”PIN

91. Prepare the machine so there is easy and safeaccess to the work area. Remove the key,disconnect the spark plug wires and maintain allsafety relat

1010. Re-install the original cutter blades that wereremoved when installing this grass catcher andsecure using the hardware removed. See Figure3-7, P

11NOTES

12GC-SFZ HOOD AND DISCHARGE ASSEMBLY3AABCCDDDDCC217554946623242251414141426272728288829303031318888141432333350505050343516163637253841394045424344484

13Ref. PartNo. Number Description28 04001-03 Bolt, Hex Head 1/4-20 x 2"29 04021-08 Nut, Elastic Stop 1/4-2030 04019-02 Nut, Serrated Flan

14GC-SFZ BAG SUPPORT COMPONENTSGC-SFZ 2007 BSC12436738910111213145

15Ref. PartNo. Number Description1 04090-02 Pop Rivet, 3/16 x .6522483589 Seal, GC Hood3 424753 Retainer, Seal4 04021-02 Nut, Center Lock 1/4-205 040

16GC-SFZ CUTTER DECK AND FRONT WEIGHT COMPONENTS1244445555666678933310111112121314141516

17Ref. PartNo. Number Description1 04003-12 Bolt, Carriage 5/16-18 x 3/4"2 424743 Baffle, LH (48" Deck)424745 Baffle, LH (52" Deck)4252

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or se

18GC-SFZ DECALS483573483569483576483039

LIMITED WARRANTY- FREEDOM Z GRASS CATCHER ACCESSORYAny part of the Scag Freedom Z Grass Catcher Accessory manufactured by Scag and found, in the reaso

PART NO. 03372PRINTED 1-2014PRINTED IN USA© 2014SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INC.WWW.SCAG.COM

11.1 INTRODUCTIONThis manual has been prepared to provide theinformation you need to correctly assemble, operate,and maintain this grass catcher. Rea

23.1 ASSEMBLY INSTRUCTIONS-NOTE-Use the illustrated parts list as a part numberreference when following the assemblyinstructions.1. Remove all packagi

35. With the cutter blades removed, refer to thefollowing steps for installation instructions of thecutter deck baffle(s) supplied with the GrassCatch

411. Install the new cutter blades included with thisgrass catcher and secure using the hardwareremoved in Step 4. On the right side of the cutterdeck

518. Install the deflector baffle included with thecatcher installation kit to the discharge boot andsecure using (2) 1/4-20 x 1" hex head bolts,

625 Install the left and right side upright mountingtubes to the grass catcher hood assembly. Secureusing (4) 3/8-16 x 2-1/4" hex head bolts and

729. Install the hose to the hood assembly and securewith (1) 8-5/8" clamp included with this grasscatcher. See Figure 3-17.8-5/8” CLAMPHOSEHOOD