Scag Power Equipment SSZ-48 Operator's Manual

MODEL GC-SSZ-48MODEL GC-SSZ-6KHOPERATORS MANUALOPERATORS MANUALOPERATORS MANUALOPERATORS MANUALOPERATORS MANUALTHIS MANUAL CONTAINS THE OPERATING

71 04021-10 Nut, Elastic Stop 5/16-182 48915 Bearing Assembly3 421319 Cover, Blower Housing4 04003-12 Carriage Bolt, 5/16-18 x .755 45565 Fan Weldment

8DECK/COUNTER BALANCE COMPONENTS (48)171451617 1815152019 23918132231322421 8 7929121728102571832111104627162625323SC001GB252333034363529A37GC-SSZ-48

91 04001-01 Bolt, Hex Head 1/4-20 x .752 48248 Tapered Hub, .875 Bore3 48924 Pulley, Tapered Bore 5.75 O. D.4 04017-28 Capscrew, Serr. Flange 3/8-16 x

10BUCKET SUPPORT COMPONENTS (UPPER)1113101219123141615A46789517SC002GB1810A20

11BUCKET SUPPORT COMPONENTS (UPPER)Ref. PartNo. Number Description1 48135-07 Hose, 6" x 48" (Model SSZ With A 48" Deck)48135-08 Hose, 6

12BUCKET SUPPORT COMPONENTS (LOWER)21311142171112221213312151691011 122331312SC015G4382372622521

1352/6148WEIGHT KITS (48, 52/61)1811191114181120191114SC003GBBUCKET SUPPORT COMPONENTS (LOWER) AND WEIGHT KITRef. PartNo. Number Description1 421309 B

14ENGINE SUPPORT COMPONENTS GC-SSZ-6KH201922232927282326312626282627 28272 4321118272630 27 28GCSSZ99ESC2414341611101391523233121525222365782737423528

151 481564 Engine, Kohler 6 hp2 45080 Blower Housing Weldment3 48136-01 Clamp, Hose 6"4 48135-08 Hose, 6" x 24"5 48136-02 Clamp, Hose 8

LIMITED LIMITED LIMITED LIMITED LIMITED WWWWWARRANTY- COMMERCIAL AARRANTY- COMMERCIAL AARRANTY- COMMERCIAL AARRANTY- COMMERCIAL AARRANTY- COMMERCIAL A

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or se

PART NO. 03064PRINTED 6/98PRINTED IN USA© 1998SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INC

®TABLE OF CONTENTSISUBJECT PAGEIntroduction ...

1INTRODUCTIONThis manual has been prepared to provide theinformation you need to correctly assemble, operate, andmaintain this accessory. Read it car

2• Loosen the right side spindle belt and remove thespindle pulley (refer to the Operator’s Manualincluded with your machine for instructions).Figure

3• Mount the counter balance rod (P/N 44093) to thespring so that the hook faces the rear of the machine.With the counter balance lever in a horizonta

4FRAME ASSY. CONT.• Mount the rear tube of the frame using four (4) 3/8-16 x 2.5" hex head bolts (A), elastic stop nuts (B),along with two (2) re

5Figure 6• Mount the rear blower housing assembly using four(4) 5/16-24 x 1" fine thread bolts and four (4) 5/16"lockwashers. Install into

6• Install the left and right brace hinge plates to thehopper cover using four (4) 3/8-16 x 1" capscrews,flat washers, and elastic stop nuts. Ti