Scag-power-equipment GC-STWC-61V User Manual

MODEL GC-STWC-61VTHIS MANUAL CONTAINS THE OPERATINGINSTRUCTIONS AND SAFETY INFORMA-TION FOR YOUR SCAG ACCESSORY. READ-ING THIS MANUAL WILL PROVIDE YO

8GC-STWC-61V BLOWER HOUSING ASSEMBLY2006 GC-STWC-61V Blower Assembly3535354789910101111121213141414141515161718192021222324242727283031323334353537383

9GC-STWC-61V BLOWER HOUSING ASSEMBLYRef. PartNo. Number Description27 04019-04 Nut, Serr. Flange 3/8-1628 04001-136 Bolt, Hex Head 3/8-16 x 1-

10GC-STWC-61V" BLOWER MOUNTING COMPONENTSUNDER SIDE OFVELOCITY-PLUSCUTTER DECK SHOWN2323282424252526261616252712345667891010111213141515161718192

11GC-STWC-61V" BLOWER MOUNTING COMPONENTSRef. PartNo. Number Description1 483227 Belt Cover, GC-61V2 04029-04 Wingnut, Plastic 3/8" Small3 4

12GC-STWC-61V BUCKET SUPPORT COMPONENTS (UPPER)1234468559999511516161616161618181313192014212122232324311153233332627282930323363735253135381715934457

13GC-STWC-61V BUCKET SUPPORT COMPONENTS (UPPER)Ref. PartNo. Number Description1 423302 Screen, Catcher Hood2 04090-02 Pop Rivet, 3/16 x .6523

14GC-STWC-61V BUCKET SUPPORT COMPONENTS (LOWER)STC 2002 BSC12111415161718192021222324413546784381267445FRAME9451010A"A"TO "A"3669

15GC-STWC-61 BUCKET SUPPORT COMPONENTS (LOWER)Ref. PartNo. Number Description1 04090-02 Pop Rivet, 3/16 x .6522 482321 Seal, Hood3 423262 Tube, Uprigh

16GC-STC DECALS482871482275481327483037481377482080483044482080482871 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS:4,487,0

LIMITED WARRANTY- COMMERCIAL ACCESSORYAny part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or se

PART NO. 03179PRINTED 8-2005PRINTED IN USA© 2005SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INC.WWW.SCAG.COM

11.1 INTRODUCTIONThis manual has been prepared to provide theinformation you need to correctly assemble, operate,and maintain this grass catcher. Rea

23.1 ASSEMBLY INSTRUCTIONS FOR 61"CUTTER DECK-NOTE-Use the illustrated parts list as a part numberreference when following the assemblyinstructio

312. Install the hopper mounting brackets to theoutside of the frame on the rear of the machine.See Figure 3-6.FIGURE 3-613. Attach the hood assembly

417. Install one 7/16-14 x 1-3/4" hex head bolt intoeach of the four mounting holes in the weightsupport bar, and through the matching holes inth

5WARNINGWARNINGDO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHINGKIT, OR ENTIRE GRASS CATCHER INSTALLED7. Re-install the side discharge chute to the ope

65.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.

7NOTES