Scag Power Equipment GC-STC-CS User Manual

MODEL GC-STC-CSTHIS MANUAL CONTAINS THE OPERATINGINSTRUCTIONS AND SAFETY INFORMA-TION FOR YOUR SCAG ACCESSORY. READ-ING THIS MANUAL WILL PROVIDE YOUW

8GC-STC 48" & 52" BLOWER HOUSING ASSEMBLYWARNINGINSTALL BELT COVER BEFOREOPERATING MACHINEREAD OPERATOR'S MANUAL2005 GC Blower Asse

9GC-STC 48" & 52" BLOWER HOUSING ASSEMBLYRef. PartNo. Number Description27 04019-04 Nut, Serr. Flange 3/8-1628 04001-136 Bolt, H

10GC-STC 48" & 52" BLOWER MOUNTING COMPONENTS123456678910101112131415151617181920390STC203B21226RIGHT SIDE OFCUTTER DECK SHOWN

11GC-STC 48" & 52" BLOWER MOUNTING COMPONENTSRef. PartNo. Number Description1 482612 Belt Cover, GC-STC2 04029-04 Wingnut, Plastic 3/8&q

12GC-STC-CS HOPPER COMPONENTSABC2008 CSHOPPEREXPLOD-STWC 11645151445435655617415054349315111405859251289344950 243429422748385310336160371936204933215

13GC-STC-CS HOPPER COMPONENTSRef. PartNo. Number Description1 483038 Hopper, GC-STC-CS2 482732 Door, GC-CS3 461626 Sweeper Weldment, GC-CS4 48

14FRONT WEIGHT COMPONENTS25431

15FRONT WEIGHT COMPONENTSRef. PartNo. Number Description1 461097 Weight Assembly2 04001-117 Bolt, Hex Head 7/16-14 x 1-3/4"3 451517 Support Weldm

16GC-STC-CS DECALS483402482275481327483391483392483393483044483392483391483393 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENT

LIMITED WARRANTY- COMMERCIAL ACCESSORYAny part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or se

PART NO. 03233PRINTED 3-2007PRINTED IN USA© 2007SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INCwww.scag.com

11. With the hopper door closed, engage the deckdrive.2. Proceed to mow until the hopper is full.A replacement manual is available from yourauthorized

23. When dumping the hopper into a disposal area:A. Disengage the deck drive, apply the parkingbrake and allow all moving parts to come toa complete s

33.1 ASSEMBLY INSTRUCTIONS FOR 48" AND 52" CUTTER DECK-NOTE-Use the illustrated parts list as a part numberreference when following th

4PROPERLYSERVICEENGINEWITHOILANDFUEL.FIGURE 3-2FIGURE 3-3ELASTIC STOPNUTFLATWASHERCARRIAGE BOLTRIGHT SIDE OF CUTTER DECK SHOWN(Note: Some parts not sh

510. Install the new belt covers and secure. Seeitems number 1 and number 21 on page 10 of theBlower Mounting Components section in theIllustrated Pa

61. Prepare the work area making sure that it is aclean, safe environment.2. Remove the rubber strap holding the adapter tothe blower assembly and the

75.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.