Scag Power Equipment GC-STT-CS User Manual

MODEL GC-STT-CSTHIS MANUAL CONTAINS THE OPERATINGINSTRUCTIONS AND SAFETY INFORMA-TION FOR YOUR SCAG ACCESSORY. READ-ING THIS MANUAL WILL PROVIDE YOUW

81. Prepare the work area making sure that it is aclean, safe environment.2. Remove the rubber strap holding the adapter tothe blower assembly. See F

95.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.

10GC-STT BLOWER HOUSING ASSEMBL YWARNINGINSTALL BELT COVER BEFOREOPERATING MACHINEREAD OPERATOR'S MANUAL2005 GC Blower Assembly123345474545678991

11GC-STT BLOWER HOUSING ASSEMBL YRef. PartNo. Number Description1 04067-07 Pin, Ring 2-1/4" Long2 481547 Lanyard, Deck Height Pin3 04019-

12GC-STT BLOWER MOUNTING COMPONENTS390STT0203DUNDER SIDE OFCUTTER DECK SHOWN2223243125262526322727282828292930123456678910101112131415151617181920216R

13GC-STT BLOWER MOUNTING COMPONENTSRef. PartNo. Number Description1 482406 Belt Cover, GC-STT - 52"483226 Belt Cover, GC-STT - 61" & 72&

14GC-STT-CS HOPPER COMPONENTSAABBCC2008 CSHOPPEREXPLODE-STT 11645151445435655617415054349315111405859251289344950 243429422748385310336160371936204933

15GC-STT-CS HOPPER COMPONENTSRef. PartNo. Number Description1 483038 Hopper, GC-STT-CS2 482732 Door, GC-CS3 461626 Sweeper Weldment, GC-CS4 48

16GC-STT FRONT WEIGHT COMPONENTS4132576

17GC-STT FRONT WEIGHT COMPONENTSRef. PartNo. Number Description1 04021-09 Nut, Elastic Stop 3/8-162 04067-06 Pin, 1/2 x 6-1/4"3 481737 Lanyar

FAILURE TO FOLLOW SAFE OPERA TING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or s

18GC-STT-CS DECALS483402482275481327483391483392483393483044483392483391483393 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENT

LIMITED WARRANTY- COMMERCIAL ACCESSORYAny part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to

PART NO. 03237 Rev.01PRINTED 6-2011PRINTED IN USA© 2011SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INCwww.scag.com

11.1 INTRODUCTIONThis manual has been prepared to provide theinformation you need to correctly assemble, operate,and maintain this grass catcher. Rea

23. When dumping the hopper into a disposal area:A. Disengage the deck drive, apply the parkingbrake and allow all moving parts to come toa complete s

33.1 ASSEMBLY INSTRUCTIONS-NOTE-Use the illustrated parts list as a part numberreference when following the assemblyinstructions.1. Remove all packagi

4PROPERLYSERVICEENGINEWITHOILANDFUEL.DISCHARGE CHUTE OPENINGFRONT OF CUTTER DECKREAR OF CUTTER DECKVIEW FROM RIGHT SIDE OF CUTTER DECKFigure 2-52"

5FIGURE 3-3RIGHT SIDE OF CUTTER DECK SHOWN(Note: Some parts not shown for viewing purposes.) 2005 GC-STC install art 3BLOWER ASSEMBLYMOUNTING BRACKETM

610. Install the belt to the spindle pulley. Whenreplacing the belt, see figure below.12. Install the hopper mounting brackets (p/n 451512& p/n 4

7FIGURE 3-6Liquid Cooled OnlyNote:Illustration is for reference only. Some parts have been removed for visual purposes and may vary depending on model